This is a Fishing bot that reppin made for Trove. I've updated it with a working bootdrop since reppin isn't updating this anymore.
Warning:
Bootdrop can only used together with a loot collector (this program will deconstruct all fish and drop the boots after that). If you don't use this with a loot collector then bootdrop will also drop your fish.
The most efficient way to do this is by fishing in your club house, putting a loot collector under water and making multiple stacks of 1 Glim by putting them in and taking them out of your personal chest.
Short instructions:
1. Open Nippyfishing.exe
2. Double check settings by clicking 'config' in the program, mark the inventory slots that shouldn't be dropped by clicking 'slot selection config show' inside the config window.
3. Double check the fishing pointer
4. Put loot collector in water
5. Press 'e' so you open up the loot collector screen
6. Start fishing
Long instructions:
How to use
The hotkeys are as followed.
NumberPad1 Start and Stop Single client.
This key will start the Auto Fish for the client in the foreground. The client must be in the foreground for this to work. If the client is already fishing it will reset the counters for that client.
NumerPad3 Stop Single client
This will stop the foremost active window client.
CTRL+NumberPad1 This will start all trove.exe clients at once.
With this hotkey will start every client open at once. Make sure you pointing at what ever liquid type you are fishing. If the cleints are already fishing. It will reset all counters for that client.
CTRL+NumberPad3 Mass Stop of all clients
This will stop all clients from fishing. They will not finish there last cast sorry.
NumberPad* Reload command
If for what ever reason you need to reload the bot. Just use this hotkey. Do not hold this key. If you do it will open alot of the same clients.
NumberPad2 Enable and Disable Anti-AFK on Single client.
Bring the client you wish to toggle this on and off to the foreground and just hit the button. It will say on and off on the gui.
Usage
How to use the GUI Controls.
How to start/stop Single client?
To Start Single Client. Select the Client from the list. Hit Start/Restart Selected Client
To Stop Single Client. Select the Client from the list. Hit Stop Selected Client
To Start All Clients. Just the Start/Restart All Clients Button.
To Stop All Clients. Just hit the Stop All Clients button.
To wipe out all Client Data hit the Wipe all clients Data. This will remove them from the list and the active scan will pick them back up as if the client was just started.
To bring the client to the foreground. Just Select the Client on the list. Then hit the button Bring selected client to foreground.
To config the bot hit the Config button.(There is not much to config so I left this as a place holder. For when the config is needed.)
If you like what you see and like to help make me want to keep releasing updates hit the donate button.
If the bot detects that is is not fishing a screen will come up with the pID. You can then just click that screen to stop that client from fishing. it will bring that window to the foreground so you know which one it is if running alot. Some times the bot might glitch and not cast so you can ignore the first one you see. But if it comes up over and over you might want to check it to resolve the issue it is having.
If you wish to fish in a new liquid type just stop the bot on that client and then start it up again facing the new liquid type.
How to use the bootdrop/decon fuctions
Put a loot collector under the water. Hit E while facing it to open that loot collector screen. Do not hit b to open bag other wise the loot collect will not work. With that setup done just start the bot up like normal.
Config GUI
In side this GUI you will see options for various things you can tweak.
Here you also can enable the boot drop. There are 3 ways to trigger the boot drop. You might not need all 3 but you can use all 3. Just tweak the settings till you get it how you like. Also there is a Ignore slot config screen. Just hit the button in the config. This will bring it up. Just check the slots you wish for it to ignore.
Notes about bootdrop. You need to be in windowed mode for this to work.
Known Issues
Once in a while it will say unknown liquid type when fishing.
Please try starting that client again to get it to change to the liquid type.
Reason for that is that you are lagging or the lure you cast did not hit the water before it tried to read the info.
So if you see any other problem please do report them.
List of current features
The bot will work with more then one client. No need to run more then one exe for each client.
More efficient at scanning memory. It wont try and scan all 3 types of liquids only the type of which it started fishing in first.
It checks to see if you have a lure in the water between 8 and 11seconds or more then 45seconds after cast. No need to wait the 40 to 45 seconds like most bots to tell the user it is not fishing.
Memory scan wont start till the lure has been in the water for more then 12 seconds. This saves on cpu usage with the bot it self.
Better error handling. Meaning it should not cast for no reason and waste lures.
No more loops for main thread. So you can stop and start with out having to reload the fishing bot it self.
Open source. I do not care if others have the source. But just remember to give credit where credit is due.
Window title change. With info of the pID of that client and if it is fishing or not.
There are others but can't seem to think of anymore atm I will fill it in as the come in.
Built in boot drop. It now has it.
Various options you can now config to tweak it.
Auto afk/Close client if the bot detects it stops fishing
Bootdrop and Decon. With slot selection to pick which slots to ignore.
Download:
see attachment
Scan:
Fishing pointer: 0x00BB0924
![[Trove] Fishbot with working bootdrop](https://www.elitepvpers.com/forum/iconimages/general-gaming-releases/trove-fishbot-working-bootdrop_ltr.gif){kind=small}
When i him start he press f about 15 sec and then jump error. Sorry for my english...
