Seriously, what the.... I compile a ConsoleApplication and it freaking uses 3,8K already >_>. Any idea why it is like that? Lmao
cool good for u i posted my serv mem usage, doubt it if u want w/e, anywayz with mob's, npc's it use's 6.2k, without dmaps tho, also that was not thru compiling it was thru the .exe
that last ss was without mob's spawned
'tearz bet u where the 1 who clicked no for adding me 2 ug (Y)
Whats this for, it's not gonna be memory usage that kills your server, it would be CPU usage. Most good computers have 4gig memory, and your < 20mb servers ram will hardly effect that.
It's to see how well your server is put together, if you were to have say 1,000 people on at a time, you'd probably use more memory than 20mb. Not that anyone's server's will have that many, but it's just about efficiency.
It's to see how well your server is put together, if you were to have say 1,000 people on at a time, you'd probably use more memory than 20mb. Not that anyone's server's will have that many, but it's just about efficiency.
Memory is not the way to see how well a server has been programmed, CPU would be, less cycles the better.
That's probably a Windows Server 03. I'm just guessing but based on the newer looking Recycle bin and older style toolbars, it's probably that, or just XP.
Private Server - Usage of Public IP 05/20/2011 - Shaiya Private Server - 13 Replies Hello.
For the past couple of days, I have been trying to run a private Shaiya server. I have followed each guide that I have used (I have performed multiple installs) to every little last detail that it gives. I am able to run the server and play on a local IP (127.0.0.1), but am entirely unable to play on the server with a public IP (69.133.XYZ.XY). Each service in the Server Patch Config utility shows green > marks all over the board. The server runs. However, upon attempting to access...
Special force 100% Memory usage!!! 12/20/2009 - Soldier Front Philippines - 18 Replies bkit ganun po ung nanyari diba nag maintenance naging 100% memory usage na ung special force ko ang nangyayari ang tagal ng loading kahit load na tapus nag laglag pa<putol putol moment> lagi nlng ganun kung cnu makakahanap ng solution my 100 ecoin po sakin !!!
[AutoIt] Tab key to cycle through hotbars 08/14/2009 - General Gaming Discussion - 0 Replies Make sure you set your hotbar changing bindings to CTRL instead of SHIFT, so it doesn't mess with you while you're sprinting.
Dim $a, $b, $c, $d, $e, $f, $g, $h
$b = InputBox( "Question", "How many different weapons to use?", "2" )
If $b = 2 Then
$c = InputBox( "Question", "Hotbar number for Weapon 1?", "1" )
$d = InputBox( "Question", "Hotbar number for Weapon 2?", "2" )
HotKeySet( "{TAB}", "Tab1" )
ElseIf $b = 3 Then
$c = InputBox( "Question", "Hotbar number for Weapon 1?", "1" )
Problems with memory usage on vista64 (/min function testosterone) 03/18/2009 - Silkroad Online - 6 Replies Hi!
Can anyone help me? Im using 64 bit vista now, and i have a multiply problem...
I remember when I used XP I typed /min in testosterone and it reduced the sro_client's memory usage from about 400k to about 50-100k....
and now on Vista64 if I type /min, the memory usage stays at 400k.. I cant reduce it...
I'm looking for a solution.. plz help...
Memory usage of conquer? 07/04/2007 - Conquer Online 2 - 2 Replies Hi guys,
i have on my new com vista... and i think co is eating too much memory after few hours it goes like 250MB and that never happened to me on XP where it was like 50-80MB did anyone experienced this too? or i just have somethin messed up...
thnx for replies