Hey Leute,
ich hoffe mir kann hier jemand helfen , undzwar habe ich folgendes Problem:
Ich hab meinen Pc jetzt neu aufgesetzt habe nun einmal XP drauf und als 2
Betriebssystem Linux Mint . Das Problem liegt jetzt bei XP , denn er erkennt meinen
Netzwerkadapter nicht oder nicht richtig da ich noch keinen Treiber installiert habe.
Das Problem jetzt ist das mir nirgendwo der genaue Name angezeigt wird und ich somit
auch nicht weiß welchen Treiber ich benötige . Ich bekomme unter Windows lediglich informationen wie "802.11n" oder "1394 netzwerkadapter" was mir nicht weiter hilft.
Unter Linux habe ich allerdings eine Wlan Verbindung mit dem Ding aber auch hier finde ich keine genaue Bezeichnung . Hat jemand vielleicht ne Idee ?
Gruss RaZor
Edit:
hwinfo --netcard
> hal.1: read hal dataprocess 31028: arguments to dbus_move_error() were incorrect, assertion "(dest) == NULL || !dbus_error_is_set ((dest))" failed in file ../../dbus/dbus-errors.c line 280.
This is normally a bug in some application using the D-Bus library.
libhal.c 3483 : Error unsubscribing to signals, error=The name org.freedesktop.Hal was not provided by any .service files
24: PCI 202.0: 0200 Ethernet controller
[Created at pci.318]
Unique ID: rBUF.MW_7j9rak0C
Parent ID: 6NW+.0DEuJolBxo7
SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:02.0
SysFS BusID: 0000:02:02.0
Hardware Class: network
Model: "Realtek RTL-8139/8139C/8139C+"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8139 "RTL-8139/8139C/8139C+"
SubVendor: pci 0x1462 "Micro-Star International Co., Ltd."
SubDevice: pci 0x204c
Revision: 0x10
Driver: "8139too"
Driver Modules: "8139too"
Device File: eth0
I/O Ports: 0xec00-0xecff (rw)
Memory Range: 0xfdefe000-0xfdefe0ff (rw,non-prefetchable)
Memory Range: 0xfdd00000-0xfdd0ffff (ro,non-prefetchable,disabled)
IRQ: 18 (91709 events)
HW Address: 00:13:d3:b1:21:94
Link detected: no
Module Alias: "pci:v000010ECd00008139sv00001462sd0000204Cbc02sc0 0i00"
Driver Info #0:
Driver Status: 8139too is active
Driver Activation Cmd: "modprobe 8139too"
Driver Info #1:
Driver Status: 8139cp is active
Driver Activation Cmd: "modprobe 8139cp"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #17 (PCI bridge)
51: USB 00.0: 0282 WLAN controller
[Created at usb.122]
Unique ID: L0iK.mnWipy+JICF
Parent ID: 2UT6.bIMjNOuhmmA
SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3.2/1-3.2:1.0
SysFS BusID: 1-3.2:1.0
Hardware Class: network
Model: "Ralink 802.11 n WLAN"
Hotplug: USB
Vendor: usb 0x13d3 "Ralink"
Device: usb 0x3247 "802.11 n WLAN"
Revision: "8.01"
Serial ID: "1.0"
Driver: "rt2800usb"
Driver Modules: "rt2800usb"
Device File: wlan0
Features: WLAN
Speed: 480 Mbps
HW Address: 00:15:af:43:3b:e2
Link detected: yes
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "usb:v13D3p3247d0801dc00dsc00dp00icFFiscFFipFF "
Driver Info #0:
Driver Status: rt2800usb is active
Driver Activation Cmd: "modprobe rt2800usb"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #49 (Hub)
Hab das über hwinfo herausgefunden blick immer noch nicht durch