[Release] L2-Zur - Undetectable - Any L2 server/version

[L2-Zur]

Originally Posted by hanamichi8186

Hi, i try to using it, and got successful , but after 2-3 mins running bot
Client and bot close. Then the small window open : The Stuck detection have been engaged. The bot and Game Client will be close.

So, what was that? How to fix it

This has been discussed in detailed atleast 3 times already, please read the thread.

[hanamichi8186]

Originally Posted by L2-Zur

This has been discussed in detailed atleast 3 times already, please read the thread.

Can you write the solution in first page , so anyone can see, and wont ask again the problem, because i see not only me ask about that

[snakesoul]

I got a problem:

I'm botting with my mage and it only targets near mobs... I mean if the mob is like 5 meters away it doesn't target it, but if I'm pretty close it targets without problem... What did I wrong?

Nice bot man! Thank you!

[L2-Zur]

Originally Posted by snakesoul

I got a problem:

I'm botting with my mage and it only targets near mobs... I mean if the mob is like 5 meters away it doesn't target it, but if I'm pretty close it targets without problem... What did I wrong?

Nice bot man! Thank you!

Use the MobLists, its covered in the tutorial vid.

[snakesoul]

Originally Posted by L2-Zur

Use the MobLists, its covered in the tutorial vid.

I did! But still doesn't work! thanks you!

EDIT: I tried using macro to /target mobname... And now I got two problems:
- Bot attacks far mobs when there is another one very close. (not important)
- It doesn't target next mob until the corpse goes away!

[L2-Zur]

Originally Posted by snakesoul

I did! But still doesn't work! thanks you!

EDIT: I tried using macro to /target mobname... And now I got two problems:
- Bot attacks far mobs when there is another one very close. (not important)
- It doesn't target next mob until the corpse goes away!

Use MobLists, if they dont work, then you didnt configure it properly.

How to use them is clearly explained in the tutorial video. With MobLists, you will have none of these problems.

[snakesoul]

Originally Posted by L2-Zur

Use MobLists, if they dont work, then you didnt configure it properly.

How to use them is clearly explained in the tutorial video. With MobLists, you will have none of these problems.

Thank you very much!! It's working now...

Just another little problem:

Sometimes the bot targets a mob that can't see (while there are others closer...) and it waits 10 sec and do what I put on config (nextarget) but near the character there isn't any mob, so it targets again the same mob! It's a loop.

Is there any way to make bot attacks closer mobs first or to fix the problem about "hidden" mobs?

Thank you very much for bot and help!

[elite_lime]

Really a very nice program, but I experience certain problems unfortunately. My program when writes /target mob_name after a minute or two starts writing arget mob_name get mob_name b_name and etc. And it always posts this on chat, so this is very bad. Any suggestions how to solve this issue?

[L2-Zur]

Originally Posted by elite_lime

Really a very nice program, but I experience certain problems unfortunately. My program when writes /target mob_name after a minute or two starts writing arget mob_name get mob_name b_name and etc. And it always posts this on chat, so this is very bad. Any suggestions how to solve this issue?

I havent had a problem like this reported yet. I would reccomend deleting everything and re-downloading the launcher again.

Then reconfigure from scratch.

[elite_lime]

Oh, a very fast reply! Thank you!

I just reinstalled and tried it again, nothing changed. Everything else is good, I followed your tutorial video and I have win 7 64bit.

My log till the problem starts occuring and I pause the hack.



Settings:

Btw, it could have something to do with windows, because I frequently check how is the bot doing and I would suspect that it is the cause.

Update: in general, bot is going crazy when Lineage 2 is not the active window.

[L2-Zur]

Originally Posted by elite_lime

Oh, a very fast reply! Thank you!

I just reinstalled and tried it again, nothing changed. Everything else is good, I followed your tutorial video and I have win 7 64bit.

My log till the problem starts occuring and I pause the hack.



Settings:

Btw, it could have something to do with windows, because I frequently check how is the bot doing and I would suspect that it is the cause.

Update: in general, bot is going crazy when Lineage 2 is not the active window.

Did you configure this? Its in the important notes in the 1st post.

Important notes:
- Botting with L2 window not having focus or in background mode requires that you disable the "Decrease Background Performance" setting in game menu in Lineage II options.
- Buffs require that you enable "Enter Chat" in shortcuts menu in Lineage II options.

[elite_lime]

Yes, it was checked by default.

[L2-Zur]

Originally Posted by elite_lime

Yes, it was checked by default.

- Botting with L2 window not having focus or in background mode requires that you disable the "Decrease Background Performance" setting in game menu in Lineage II options.

It has to be unchecked.

[Kacko777]

Any chance that this bot will work on 32bit in future?

[elite_lime]

Thank you, works fine I guess now. Is it possible to turn off stuck protection? I want to move my character by myself when its stuck, because I usually use it when I'm not afk. Indeed, a very good bot, great job coder Looking forward to new updates. I love your attitude to avoid getting caught and making this bot safe.

Btw, any suggestion why it sometimes starts opening inventory/character info and etc windows when I am switching between windows (l2 and eg chrome)?

Looks like the above problem doesn't occur so frequently now. Dunno why.. Another problem is that sometimes the bot writes in the log window that it is attacking something with my attack button, but it doesn't have actually any target or mob.