Neuen Computer zusammengebaut, aber ...

04/03/2012 12:35 wutax#16
So hier einmal die Fotos:

Die Grafikkarte:
(Bitte achtet nicht auf die schreckliche Verlegung der Kabel, das Netzteil bringt nur solche kurzen mit..)
Im liegen sieht man es nicht so stark..
[Only registered and activated users can see links. Click Here To Register...]

Die Pins:
(Ich weiß, schreckliche Qualität, hab es nicht besser hinbekommen..)
Hab' mal die Reihenfolge von links nach rechts von oben nach unten dazugeschrieben..
[Only registered and activated users can see links. Click Here To Register...]
Ja, ich arbeite gerne mit sauberen Handschuhen ^^

Das Mainboard:[Only registered and activated users can see links. Click Here To Register...]
Und ganau hier passen die Pins nicht hinein..
04/03/2012 12:59 Kuh#17
jop rund darf ins eck ;)

ich verstehe nicht wirklich, warum das nicht passen sollte.

und deine grafikkarte ist noch ne ganze ecke grader als meine ;)
aber die ide festplatte solltest du dringend mal austauschen

ps: natürlich kann ich auch nur nach bestem wissen und gewissen beraten. Bevor du deinen pc in flammen aufgehen siehst, warte lieber noch auf eine 2. meinung :P
04/03/2012 13:27 wutax#18
Quote:
Originally Posted by Kuh View Post
jop rund darf ins eck ;)

ich verstehe nicht wirklich, warum das nicht passen sollte.

und deine grafikkarte ist noch ne ganze ecke grader als meine ;)
aber die ide festplatte solltest du dringend mal austauschen

ps: natürlich kann ich auch nur nach bestem wissen und gewissen beraten. Bevor du deinen pc in flammen aufgehen siehst, warte lieber noch auf eine 2. meinung :P
Also du meinst, dass man einen runden Pin in ein eckigen Slot schieben darf? Ja, ich vertraue dir zwar, aber ich warte doch lieber noch auf eine 2. Meinung.
Und was meinst du mit IDE Festplatte? Das ist eine ganz neue SATA III Caviar Black 64MB 7.200U/min ;) Meinst du, ich soll auf eine SSD umsteigen oder wie?

#Edit
War schnell im Bauladen und hab' mir ein rundes Holzstück schneiden lassen (15,8cm). Dann mit so einem Patterfix oben und unten etwas festgemacht (nicht geklebt :D). Das Ergebnis ist überraschend. Jetzt muss ich mir darüber keine Gedanken mehr machen.

#Edit2
Der Typ hat anscheinend das gleiche Problem :D
[Only registered and activated users can see links. Click Here To Register...]
Wäre nett, wenn mir jemand folgende Frage beantworten könnte:
Kann man den 8-Pin Stecker in das Mainboard stecken, wenn die Kodierung nicht passt, aber es ohne Gewalt in das Mainboard eizustecken wäre?
04/03/2012 14:17 Kuh#19
Quote:
Motherboards can come with either a 4 pin 12 volt connector or an 8 pin 12 volt connector. Many power supplies come with a 4+4 pin 12 volt cable which is compatible with both 4 and 8 pin motherboards. A 4+4 power cable has two separate 4 pin pieces. If you plug the two pieces of a 4+4 power cable together then you have a 8 pin power cable which can be plugged into an 8 pin 12 volt connector. If you leave the two pieces separate then you can plug one of the 4 pin pieces into a 4 pin 12 volt connector and leave the other 4 pin piece unplugged.

If you look carefully at the image above then you can see the polarization of the pins which prevents you from plugging the cable in improperly. Some of the pins are square and some of them have rounded off corners. The motherboard connectors have matching square and rounded off corners to prevent the cable from being plugged in the wrong way. But if you look really carefully at the right half of this particular cable and then look at the 8 pin 12 volt cable pictured above you'll notice that they don't match. A regular 8 pin cable has four square pins and four rounded ones but the 4+4 cable shown above has two square pins and 6 rounded ones. The left half of the 4+4 matches the left half of an 8 pin cable but the right half is different. Hmmmm... And this isn't some bizarre cable either. I've seen plenty of 4+4s which look like this one. And then there are other 4+4 cables which look just like an 8 pin cable split in two (which makes sense). Since rounded pins fit into square holes in motherboard connectors, this particular cable will fit just fine into an 8 pin 12 volt motherboard connector. But both halves of this 4+4 will fit into a 4 pin 12 volt motherboard connector. You're supposed to use the left half of the cable shown above when plugging it into a 4 pin motherboard connector but the right half will also fit. As it happens, either half will work fine in a 4 pin motherboard because both halves of the 4+4 just provide 12 volts. The pinouts are the same for both halves so either one will work. I'm not sure why they make cables like this one because you'd figure a 4+4 cable would just be an 8 pin cable which splits in two. And you only need one half of a 4+4 cable to plug into a 4 pin motherboard. The other half is unused. But the kind of 4+4 cable shown above is pretty common so don't let it throw you.
hab grad noch mal rum geschaut zu dem thema und diesen link gefunden:
[Only registered and activated users can see links. Click Here To Register...]

ach und bei der festplatte hab ich mich einfach verguckt :) hatte da nur am anfang 1 mal rüber gescrolled..

und zu der frage, ob man ein anderes 8 pin dort rein stecken darf: Soweit ich weiß nein. Die anderen 8 pin sind für pciE (also graka etc)
04/03/2012 14:25 wutax#20
Quote:
Originally Posted by Kuh View Post
hab grad noch mal rum geschaut zu dem thema und diesen link gefunden:
[Only registered and activated users can see links. Click Here To Register...]

ach und bei der festplatte hab ich mich einfach verguckt :) hatte da nur am anfang 1 mal rüber gescrolled..

und zu der frage, ob man ein anderes 8 pin dort rein stecken darf: Soweit ich weiß nein. Die anderen 8 pin sind für pciE (also graka etc)
Du redest aber jetzt von den 6 pin PCI Express + 2 pin PCI Express, oder?
Das heißt, dass ich die 2 mal 4 pin hineinstecken darf, egal wie diese aussehen, oder?
04/03/2012 14:50 Kuh#21
das war nur die antwort auf die
Quote:
Kann man den 8-Pin Stecker in das Mainboard stecken, wenn die Kodierung nicht passt, aber es ohne Gewalt in das Mainboard eizustecken wäre?
da ich nicht wusste, ob sie nur unglücklich formuliert war, oder ob du anstatt der 2x4 12v kabeln ein 8 pin pciE kalben nehmen wolltest :)

Und wie gesagt, ich glaube Ja, du darfst den 2. 4 pin dazu stecken, der zitierte artikel dort auch und trotzdem würde ich noch auf eine weitere meinung warten.

Du könntest vll auch den händler fragen, falls du bei Alternate oder so gekauft hast, helfen die dir sicher gern.
04/03/2012 14:57 wutax#22
Dann erstmal ein großes DANKE!
Ich werde es jetzt einfach probieren. Wieso sollte es nicht klappen, Asus und auch BeQuiet sind doch zwei richtig erfolgreiche und moderne Firmen. Die werden das doch nicht so machen, dass es piep wenn kein zweiter 4Pin Stecker drinnen steckt, aber man den zweiten 4Pin Stecker nicht anschließen kann.

#Edit:
Klappen tut es, jedoch ist das piepen wie auch die Meldung "No Device!" nicht verschwunden. Das heißt wohl, ich muss weitersuchen. D:
04/04/2012 02:41 LuCk3r#23
Das Piepen ist normal.
Wann kommt diese No Device Meldung? Die sagt mir irgendwie nix, am besten mal Screenshot/Foto von.
04/04/2012 09:03 wutax#24
Quote:
Originally Posted by LuCk3r View Post
Das Piepen ist normal.
Wann kommt diese No Device Meldung? Die sagt mir irgendwie nix, am besten mal Screenshot/Foto von.
Diese Meldung habe ich nun weg bekommen und der PC startet viel schneller. Das Problem war, dass ich den VIA Contoller aktiviert hatte...
Trotzdem danke. Und das mit dem piepen ist offenbar normal. Weil es macht keinen Sinn wenn es piepst, aber keine Fehler oder Anzeichen auf Fehler auftauchen.