Dyelite link?

Quote:

Originally Posted by craddle Here's a copy of Realback's Guild site Dye lite guide. Dye Lite Mod Download: [Only registered and activated users can see links. Click Here To Register...] Simply download and extract to any desired location via winrar. Youtube Dye Lite Guide:[Only registered and activated users can see links. Click Here To Register...] BEFORE YOU START , RUN MABINOGI as WINDOW MODE!!!! Full Screen Mode doesn't work with dye program! 1. Let's Set up the color ! [Only registered and activated users can see links. Click Here To Register...] Watch Carefully on this part! I just did the custom color such as blue, yellow, etc. Black , White, Red will be all different. 1. Web Color code : You can get this one from Web color code source. (check the board) 2. Minimum amount of points that you want to get. 3. Error Percentages. ******************IMPORTANT******************** For Fabric, Black : You need to set up as 20~25 for Error Percentage.. Can set up 2~4 color points (mostly 3.) settting up by 4 will take alot of time. Web color code, #000000 For Leather, Black : You can't get more than 2, set up minimum point as 1, with 'RGB 1,1,1' code. Set up Error Percentage as '0' For Fabric, White : You need to set up error percentage as '30~40', recommend 30. Can set up 2~4 color points, but hard to get 4 of them. Recommend to set up 3. RGB code 255 255 255. For Leather, White : same as Black for Leather, there's no real white color points. It's up to you. I will not mention about Silk. Read the previous thread. For Fabric, Red : HARDEST one to get. Need to set up as 30~40 for Error Percentage. can get only about 1~3, but mostly 2 points. Web Color code.. #990000 <important For Fabric, Any other custom colors : set up 30~50 Error Percentage. set up 2~4 points (blue/greens are easy to get.) RGB codes are on the board. Read it. 2. Start. If you are all set and good to go, press '염색시작' which means 'Start dying' Then you will see little window pops up like below. [Only registered and activated users can see links. Click Here To Register...] 3. Running Dyeing Form! [Only registered and activated users can see links. Click Here To Register...] Choose the part you want to dye. Then press 'pick color' 4. Dye Cycle (important) [Only registered and activated users can see links. Click Here To Register...] Now, you can see those 'RGB' codes below each numbers. When you clicked 'Pick Color' Button previously, then move your mouse cursor to the dye pallet. Then it will be appeared. If dye program found the color points as you set up on part #1, then simply click on the pallet so you can make final decision. I mean, click the left button of your mouse so time doesnt keep going away. Then press 'Start Dyeing'. But if you don't like its combination or did not find the color points in 1~3 seconds, then press either cancel or part C(that you selected) for reseting the pallet. Then press 'Pick Color' Button Again. As you can see, you can see the cycle. 1. Pressing Pick Color 2. Move your Cursor on the Pallet A. If dye program found the point and if you like its color and combination, click on the pallet, then click 'Start dyeing' Button. B. If dye program didn't find the color point in 1~3 seconds, click 'cancel' or 'Part'(that you chose) Button. Then go back to Step #1. When dye program did not find the color point, your step will be like 1 -> 2-> B -> 1 -> 2 -> B ....... [Only registered and activated users can see links. Click Here To Register...] When Dye Program found the points as you set up, RGB code will be appeared in the red box which tells you that's the color (with some calculation of error percentages. So, other than Black and White, it will be hard to get exact same color) Dye Color Code Chart: [Only registered and activated users can see links. Click Here To Register...] Good Luck ;)

Quote:

Originally Posted by cloudkiller2006 for some reason dyelite gives an error instead of putting down a X<-- HERE for where to click and yes i am using the vista version and yes i run as admin

Quote:

Originally Posted by Mikirou I'm just looking at this thing for the heck of it. Just to see if I can get it to work. But that's the problem...the screen won't resize enough for me to press start...so...how can I get it to resize?