FTP connection fail

07/24/2015 23:22 mlukac89#1
Hi, i have problem with connection on ftp with example script i get message all time "ERROR = -1", but in filezilla or other ftp client i connect normally with same data ?
And what this _FTP_Open('') means, i can write what i want in ? like this is my connection name or something from server ?
thanks in advance


Code:
#include <FTPEx.au3>
#include <MsgBoxConstants.au3>

Local $sServer = '**********'
Local $sUsername = '*******'
Local $sPass = '*********'

Local $hOpen = _FTP_Open('MyFTP Control')
Local $hConn = _FTP_Connect($hOpen, $sServer, $sUsername, $sPass)

If @error Then
    MsgBox($MB_SYSTEMMODAL, 'FTP Connection : ', 'ERROR = ' & @error)
Else
    MsgBox($MB_SYSTEMMODAL, 'FTP Connection : ', 'Connected')
EndIf
Local $iFtpc = _FTP_Close($hConn)
Local $iFtpo = _FTP_Close($hOpen)
07/24/2015 23:26 alpines#2
The _FTP_Open is probably the UserAgent. Your data must be wrong then, check your servername / username / pass and retry again. Also try to run the program with elevated privileges.
07/24/2015 23:52 mlukac89#3
Ah works just added #RequireAdmin, stupid windows 8 :)

Now have same problem with GUI but all works fine just dont want to connect again throws error -1, i try to compile ( x64 ) and run as admin, try to run script just in x64


Code:
#RequireAdmin
#include <ButtonConstants.au3>
#include <ComboConstants.au3>
#include <EditConstants.au3>
#include <GUIConstantsEx.au3>
#include <StaticConstants.au3>
#include <WindowsConstants.au3>
#include <FTPEx.au3>

#Region ;**** Directives created by AutoIt3Wrapper_GUI ****
#AutoIt3Wrapper_Compression=4
#EndRegion ;**** Directives created by AutoIt3Wrapper_GUI ****

#Region ### START Koda GUI section ###
$GUI = GUICreate("FTP tool", 308, 242, 643, 265)
GUICtrlCreateLabel("Host", 16, 16, 26, 17)
GUICtrlCreateLabel("Port", 192, 16, 23, 17)
GUICtrlCreateLabel("Username", 16, 56, 52, 17)
GUICtrlCreateLabel("Password", 16, 88, 50, 17)
GUICtrlCreateLabel("Status : ", 8, 152, 43, 17)
$status = GUICtrlCreateLabel("Not connected", 52, 152, 221, 17)
$host = GUICtrlCreateInput("", 48, 12, 121, 21)
$port = GUICtrlCreateCombo("", 224, 12, 65, 25, BitOR($CBS_DROPDOWN,$CBS_AUTOHSCROLL))
GUICtrlSetData(-1, "21|80")
$username = GUICtrlCreateInput("", 79, 52, 121, 21)
$password = GUICtrlCreateInput("", 79, 81, 121, 21, BitOR($GUI_SS_DEFAULT_INPUT,$ES_PASSWORD))
$connectBtn = GUICtrlCreateButton("CONNECT", 56, 192, 75, 25)
$disconnectBtn = GUICtrlCreateButton("DISCONNECT", 143, 192, 107, 25)
GUISetState(@SW_SHOW)
#EndRegion ### END Koda GUI section ###

If GUICtrlRead($status) = 'Not connected' Then GUICtrlSetState($disconnectBtn, $GUI_DISABLE) ; disable disconnect button
GUICtrlSetData($port, '21') ; default port

Global $status, $host, $port, $username, $password

While 1
    $nMsg = GUIGetMsg()
    Switch $nMsg
        Case $GUI_EVENT_CLOSE
            Exit
        Case $connectBtn
            _connectFTP()

    EndSwitch
WEnd

; connection to FTP server
Func _connectFTP()

    Local $_host = GUICtrlRead($host) ; host name
    Local $_username = GUICtrlRead($username) ; username
    Local $_password = GUICtrlRead($password) ; password
    Local $_port = GUICtrlRead($port) ; port

    Local $FTPopen = _FTP_Open('FTP connection test') ; name of connection
    Local $FTPConnect = _FTP_Connect($FTPopen, GUICtrlRead($_host), GUICtrlRead($_username), GUICtrlRead($_password), "", GUICtrlRead($_port)) ; connect

        ; try to connect to server
        If Not @error Then ; if not error
            GUICtrlSetData($status, "Connected") ; set status to connected
            GUICtrlSetState($connectBtn, $GUI_DISABLE) ; disable connect button
        Else
            MsgBox(48, 'FTP connection error', "Can't connect to server, error = " & @error) ; if there is connection error
            MsgBox(48, 'Test variables', 'server name = ' & $_host & ', username = ' & $_username & ', password = ' & $_password & ', port = ' & $_port) ; debugg message
        EndIf


EndFunc
SOLVED mistake was that i read here already filled variables

Code:
Local $FTPConnect = _FTP_Connect($FTPopen, GUICtrlRead($_host),  GUICtrlRead($_username), GUICtrlRead($_password), "",  GUICtrlRead($_port)) ; connect

; need to be

Local $FTPConnect = _FTP_Connect($FTPopen, $_host, $_username, $_password, '', $_port) ; connect
08/03/2015 09:54 Lawliet#4
#closed