[GUIDE]How turn off the dungeon TIMER!

Quote:

Originally Posted by juandelacruz1103 @podbot no offense sir but i think if you'll learn english, then we can communicate easily and clearly. coz we have a hard time reading your helpful guide.

Quote:

Originally Posted by podbot i edited... i hope now not so hard:P btw the other option: if u learn my langugage :P :D:D

Quote:

Originally Posted by podbot For this hack, you need Cabal (any type) + Cheat Engine [Part 1: Dungeon Timer] 1: buy Ruina Station and Defected Train Card entries 2: go at the entrance of Ruina Station 3: in CE search: with "4 bytes" "Smaller than..." options, value: "2" 4: after go inside of Ruina Station but don't start the dungeon, and search "Changed Value" (it's take more time, because of many address) 5: stay inside, but don't click or do anything, just search again in CE: with "smaller than" option, value: "2" 6: then 10-20 times search: "unchanged value" (if all ok, ca. 50K address left) 7: after that go outside ( so click on Exit ), but don't search again! 8: go inside of Defected Train and inside search again "unchanged value" 10-20 times (because like in Ruina Station, the timer is active) 9: go outside ( so click on Exit ), and in Fort Ruina and serach "exact value" : "0" 10: go back to town, with Return Stone and serach: "Unchanged value" (because the timer is off) 11: if u still have too many address then go In Warp Center and search still: "Unchanged value" 12: go in Lakeside, Port Lux or all other NORMAL maps and search still: "Unchanged value" -tip: if too many address still u have, then log in with other character, change the channel, but don't go in dungeons! 13: IF ONLY 100-150 address left, then can u go the next step 14: now look the addresses, select ALL, and add to the address list (red arrow) 15: many addresses are similar, but on the list few have other memory address! 16: go back in Ruina Station, and change those addresses back to: 0 17: now if all ok, you don't see the quest window and the timer. 18: try each addresses changing one by one, and find the right one If u turn off the timer, u can stay in the dungeon... if u don't know why good that... then don't do it.

Quote:

Originally Posted by [GM]DeathAngel Wtf,how did you do it cddvdxd?Send me a pm.

Quote:

Originally Posted by gogomania1 Man i got 124.xxx.xxx of results on first scan. After 10 "next scan" i've got 119.xxx.xxx scans, after 20 scans (that took me about 30 min) 116... Maybe i've read your post wrong. Please do the short explain of: 2: go at the entrance of Ruina Station - you mean just go and dont enter yet? Stand infront dungeon? 3: in CE search: with "4 bytes" "Smaller than..." options, value: "2" - when im standing infront dungeon i dont click "New Scan" im just configure my CE with this value right? 4: after go inside of Ruina Station but don't start the dungeon, and search "Changed Value" (it's take more time, because of many address) - now i enter to dungeon and press "New Scan" with value 2/4 bytes/smaller then... or i miss understand the word "Changed Value"?

Quote:

Originally Posted by bartbilf 10 easy steps to do it, only ONE entry needed! 1. Get 1 Entry item (doesn't matter which one) 2. Put ''Memory Scan Options'' from 00000000 to 20000000 3. Enter dungeon but DON'T press on ''challenge'' 4. Scan for ''1'' 5. Now press on ''EXIT'' (this way you will keep your dungeon entry) 6. Once you are out search for 0 7. Repeat Step 3 - 6 untill you have about 10 addresses 8. Pick out the 3 addresses with the same prefix (at my client it is always 17xx xxxx) 9. Go in dungeon, do NOT press ''challenge'' yet. 10. Now try to change the 3 address you found to 0. (You will notice that one is the timer address, one will make the ''challenge or exit screen'' go away *, other one I don't know yet) *change back to 1 to make screen to start dungeon appear again) PS if you give me thanks, give the Thread Starter a thanks as well, without him I would not have been able to make this ''guide''

Quote:

Originally Posted by gogomania1 What about "Scan Type"? "Value Type"?

Quote:

Originally Posted by gogomania1 What about "Scan Type"? "Value Type"? edit: ok i found it myself 4 bytes/exact value. I've tried this and it is working for switch off/on timer but only visualy. When i put value "1" back on timer address the time was still caunting. I switched timer OFF (19:00 min) when i did switch ON it was 17:40min. So actualy it is not working.

Quote:

Originally Posted by dani3266444 I keep getting 16K+ adresses and theire numbers are shrinking with like 10-15/0-1 scan.What am i doing wrong?

Quote:

Originally Posted by dani3266444 I did that 1 too. Anyway with some lucky guesses and eliminations i removed the stuff it was ment to be removed. May i also ask you a question. I changed some adresses and i could walk the dungeon w/o pressing START but i changed so many adresses at the same time (1k+) that i had no mobs and quests werent triggering any bosses/chests. Here is the question. I know its possible to use only 1 entry and enter a dung X times but how is this possible... where should i start my research ? THX in advance